|
OEM HP Compatible 180W Micro ATX
mATX Power Supply, SFX form factor with 4-Pin Video Connector. OEM HP Compatible
Power Supply Replacement HIPRO HP-K1603A3, HP-K1363A3, 0950-3602, 0950-3746, 0950-3657,
5184-2191, 5185-2974, Bestec ATX-100-5, ATX-150, ATX-1523D, ATX-1523F, & More*
AC Input is positioned on the long side (4.9") of the power supply. 3 Mounting
Holes on each side.COMES
WITH 4-PIN VIDEO POWER CONNECTOR!
Works with most HP Pavilions: 4402(H), 4403, 4404(H),
4405, 4407(H), 4409(H), 4410(H), 4411(H), 4413(H), 4415, 4416(H), 4420,
4422(H), 4430, 4431, 4433, 4435, 4437, 4440, 4443, 4445, 4450, 4451, 4453, 4455, 4456,
4457, 4458, 4463, 4473, 4483, 4509, 4510, 4512, 4515, 4530, 4531, 4533, 4535, 4536, 4537,
4540, 4541, 4550Z, 4553Z, 4563Z, 6506, 6508, 6511, 6531, 6532, 6535, 6540C, 6545C, 6551,
6553, 6563Z, 6573Z, 6615, 6623, 6633C, 6640C, 6641, 6643, 6646C, 6647, 6648C, 6651, 6653C,
6657, 6671, 6721, 6727, 6751, 6757, 6761C, 67XX, 6831, 6832, 6837, 6839, 6841, 6842, 6849,
68XX, XE730, XE743, XE783, XE839 XG836, & More*.
***Important note about our
OEM HP replacement power supply:
- If your system is not a Pentium
4 and does not require the 4-Pin Video Power Connector, please order the HPPS9006 (CLICK HERE) instead!
YOU CAN SAVE $4.00...
- OEM compatible replacement power
does not have a 3-Pin Connector (P7 or P9) for motherboard power supply fan control.
The newer power supplies have this feature already built-in to the power supply and
operates without this connector. Note:
Simply tie off the unused connectors: floppy connector & the extra peripheral
connectors when not in use by your computer. This will not cause any harm to the
system or its performance
Power Connectors including:
- (1) 20Pin ATX Motherboard Connecor
- (1) 12V 4Pin Connector
- (1) 4 Pin Video Power Connector
- (3) Peripheral Connectors &
- (1) Floppy Drive Connector
Features:
- Dimension:
4.9" x 3.9" x 3.0"
- The higher wattage means our
replacement delivers more power than the original part which enables support for more
add-on peripherals (hard drive, CDRW, DVDRW etc.). It's a feature that will benefit,
not harm your system performance.
- High efficiency
- Low ripple & Noise
- Output over voltage
protection
- Short circuit protection on
all output
- Reset table power shut down
- Approve by UL, CAS TUV,
NEMKO CB
- Internal 12VDE fan
- 100% burn-in under high
ambient temperature (50degrees C)
- Vacuum-impregnated
transformer
- MTBF: 100K hours at
25degrees C
- 100% Hi-pot tested
- Line input fuse protection
Input Characteristics:
- Voltage: 115/230 VAC
- Frequency: 47Hz to 63Hz
- Inrush current: 50A cold,
70A warm at 132 VAC
- Input current: 6.0A maximum
/ 115V, 60Hz
- 3.0A maximum / 230V, 50Hz
|
Specifications:
- Remote ON/OFF Control: The
Power supply shall accept a logic open collector level which will disable /enable all out
put voltage (excluding +5V standby).
- Temperature range:
operating 0degrees C~50degrees C storage-20degrees C~+65degrees C
- Temperature
coefficient:0.01%degrees C
- Transient response: output
voltage recovers in less than 1 ms max. following a 25%load change
- Hold-up time: 16.6ms
minimum - at 115V/60Hz.
16.6ms minimum - at 230V50Hz.
- Dielectric withstand: input
/ output 1800VAC for1 second, input to frame ground 1800VAC for 1 second
- Humidity: 5~95% RH
- Efficiency: 65% min. 70%
typical, at full load
- Power good signal: turn-on
delay 100ms to 500ms
- Over voltage protection: +5V output
6.5V
+3.3V output 4.6V
+12V output 15.5V
|
| Output Voltage |
Minimum Load |
Normal Load |
Maximum Load |
Load Reg. |
Line Reg |
Ripple & Noise |
| +3.3V |
0.5A |
8.3A |
11.5/16.7A |
+5% |
+1% |
50mVP-P |
| +5V |
1.0A |
6.3A |
16/12.6A |
+5% |
+1% |
50mVP-P |
| +12V |
2.0A |
2.0A |
10A |
+5% |
+1% |
120mVP-P |
| -12V |
0.0A |
0.15A |
0.3A |
+10% |
+2% |
120mVP-P |
| +5Vsb |
0.0A |
1.0A |
2.0A |
+5% |
+1% |
50mVP-P |
|
